1. Announcement:
    new site
    3DPFadmin (Administrator)
    07-23-2016
    Views:
    41,663
Page 1 of 2 12 LastLast
Threads 1 to 20 of 23

Forum: Hardware (stepper motor, drivers Etc)

Discuss DIY Hardware-Stepper motors, Drivers, switches etc...here!

  1. Question Internal connections on MKS GEN V1.4

    Started by cold_matter, 01-29-2018 01:48 PM
    3d printer, arduino, arduino mega, controller, driver, firmware, mainboard, mks-gen-v1.4, order, pla, plan, printer, printing, project, stepper
    • Replies: 0
    • Views: 1,544
    01-29-2018, 01:48 PM Go to last post
  2. Connecting powerful lasers

    Started by gf_endurance, 06-23-2017 09:33 AM
    000, 3d printer, cnc, contacts, control, control board, diy, driver, engraver, hand, how to connect a laser, kit, laser, laser connection, laser connector, lasers, power supply, printer
    • Replies: 0
    • Views: 1,542
    06-23-2017, 09:33 AM Go to last post
  3. Building a printer..

    Started by ChristopherBishop, 03-06-2017 10:44 PM
    abs, aluminum, art, bed, build, buy, cnc, custom, design, error, extrusion, future, heat, large, larger, location, made, mightyboard, pcb, printer, printers, set, size
    • Replies: 0
    • Views: 1,778
    03-06-2017, 10:44 PM Go to last post
  4. Geeetech GT2560 Rev A iscp connection

    Started by Sweetwater, 01-12-2017 12:33 PM
    3d printer, arduino, cheap, kit, printer, prusa i3
    • Replies: 1
    • Views: 3,076
    01-15-2017, 05:29 PM Go to last post
  5. Complete newbie with lots of questions

    Started by Alexvw, 08-29-2016 05:57 AM
    build, cnc, heat, kit, learn, newbie, parts, printer, problem, software, stepper
    • Replies: 2
    • Views: 2,356
    09-12-2016, 09:24 PM Go to last post
  6. Standoffs or spacers between Arduino and RAMPS?

    Started by Galane, 04-20-2016 02:21 AM
    arduino, clone, dremel, power, ramps
    • Replies: 0
    • Views: 2,315
    04-20-2016, 02:21 AM Go to last post
  7. NEED HELP Stepper Motors - how do you pick one?

    Started by Joshitravels, 04-14-2016 04:59 PM
    3d printed, 3d printer, cheap, learn, made, parts, printed, printer, size, stepper, toys
    • Replies: 1
    • Views: 1,835
    04-14-2016, 10:34 PM Go to last post
    • Replies: 1
    • Views: 1,801
    04-14-2016, 01:42 AM Go to last post
  8. DRV 8825's and how they work?

    Started by lorcoft, 12-17-2015 04:45 PM
    drv8825, hardware, heat, hot, motor over heating, printer, printing, stepper, vref optimisation
    • Replies: 4
    • Views: 3,774
    12-20-2015, 01:10 AM Go to last post
  9. Delta 3D Printer Motor Issues

    Started by Deus_Ex_Machina, 11-28-2015 10:37 PM
    3d printer, art, build, configuration, delta, printer
    • Replies: 2
    • Views: 2,350
    11-29-2015, 01:57 PM Go to last post
  10. Where do your get your hardware

    Started by 3DPFadmin, 12-19-2013 09:56 PM
    3d printer
    • Replies: 2
    • Views: 3,829
    08-25-2015, 10:50 PM Go to last post
  11. Gremlins in otherwise working printer

    Started by mejasont, 08-18-2015 04:43 AM
    company, hardware, hot, printer, professional, reprap
    • Replies: 2
    • Views: 2,250
    08-19-2015, 04:09 PM Go to last post
  12. Rails

    Started by dasaint80, 05-08-2015 04:07 PM
    buy
    • Replies: 1
    • Views: 2,142
    05-18-2015, 07:05 PM Go to last post
  13. choice of stepper motor size

    Started by hamonic, 04-21-2015 03:51 AM
    a4988, driver, large
    • Replies: 0
    • Views: 1,733
    04-21-2015, 03:51 AM Go to last post
  14. NEED HELP Custom 3D printer-HW questions

    Started by Pranja, 11-13-2014 06:44 PM
    3d printer, bed, custom, design, hardware, hot end, printer, specs
    • Replies: 3
    • Views: 5,103
    11-16-2014, 10:00 AM Go to last post
  15. DISCUSSION Opinions on this kit?

    Started by Galane, 07-06-2014 12:33 AM
    build, diy, elecfreaks, kit, printer
    • Replies: 2
    • Views: 2,345
    09-04-2014, 09:23 PM Go to last post
  16. Stainless threaded rod use?

    Started by largeformat3dprinter, 01-06-2014 09:40 PM
    2 Pages
    1 2
    custom, hardware, printer
    • Replies: 11
    • Views: 6,956
    06-05-2014, 01:00 PM Go to last post
  17. Guide wheels for 40mm extrusion?

    Started by Galane, 01-04-2014 06:40 AM
    3d printer, build, free, guide
    • Replies: 1
    • Views: 2,193
    02-12-2014, 04:11 PM Go to last post

Page 1 of 2 12 LastLast

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 1 users browsing this forum. (0 members & 1 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •